tipp2014 January 2014

tipp2014@nikhef.nl

17 participants
185 discussions

[Tipp2014] [Indico] New abstract submission: BOMBEN, Marco
by noreply-indico-team＠cern.ch 21 Jan '14

21 Jan '14

The following email has been sent to BOMBEN, Marco: === Dear Marco Bomben, The submission of your abstract has been successfully processed. Abstract submitted: <https://indico.cern.ch/userAbstracts.py?confId=192695>. Status of your abstract: <https://indico.cern.ch/abstractDisplay.py?abstractId=18&confId=192695>. See below a detailed summary of your submitted abstract: Conference: Tipp 2014 - Third International Conference on Technology and Instrumentation in Particle Physics Submitted by: BOMBEN, Marco Submitted on: 21 January 2014 14:27 Title: Performance Of Thin Edgeless N-on-p Planar Pixel Sensors For ATLAS Upgrades Abstract content In view of the LHC upgrade phases towards the High Luminosity LHC (HL-LHC), the ATLAS experiment plans to upgrade the Inner Detector with an all-silicon system. Because of its radiation hardness and cost effectiveness, the n-on-p silicon technology is a promising candidate for a large area pixel detector. The paper reports on the joint development, by LPNHE and FBK, of novel n-on-p edgeless planar pixel sensors, making use of the active trench concept for the reduction of the dead area at the periphery of the device. After discussing the sensor technology, a complete overview of the electrical characterization of the produced devices will be given, together with results on the charge collection efficiency. Measurements on irradiated devices will be presented too. The results will be compared to device simulations we run and to other current edgeless planar productions aimed at the ATLAS tracker upgrade for the HL-LHC. Eventually results from beam test measurements with minimum ionizing particles, such as hit and charge collection efficiency - in particular at the sensor periphery, for these edgeless sensors will be discussed. Summary Primary Authors: BOMBEN, Marco (Centre National de la Recherche Scientifique (FR)) <marco.bomben(a)cern.ch> Co-authors: CALDERINI, Giovanni (Centre National de la Recherche Scientifique (FR)) <giovanni.calderini(a)lpnhe.in2p3.fr> MARCHIORI, Giovanni (LPNHE Paris) <giovanni.marchiori(a)cern.ch> CHAUVEAU, Jacques (Centre National de la Recherche Scientifique (FR)) <chauveau(a)in2p3.fr> LA ROSA, Alessandro (Universite de Geneve (CH)) <alessandro.larosa(a)cern.ch> GIACOMINI, Gabriele (Fondazione Bruno Kessler) <ggiacomini(a)fbk.eu> BOSCARDIN, Maurizio (FBK Trento) <boscardi(a)fbk.eu> ZORZI, Nicola (Fondazione Bruno Kessler - FBK) <zorzi(a)fbk.eu> BOSISIO, Luciano (Universita e INFN (IT)) <bosisio(a)ts.infn.it> BAGOLINI, Alvise (Fondazione Bruno Kessler, Centro per i Materiali e i Microsistemi (FBK-CMM) Povo di Trento (TN), Italy) <bagolini(a)fbk.eu> Abstract presenters: BOMBEN, Marco Track classification: Sensors: 1b) Semiconductor Detectors Experiments: 2a) Experiments & Upgrades Presentation type: --not specified-- Comments:

1 0

[Tipp2014] TIPP2014 / iseg
by Maik Donix 21 Jan '14

21 Jan '14

Dear Sir or Madam, we iseg Spezialelektronik GmbH (developer and manufacturer of precise high voltage power supplies) would like to exhibit at TIPP2014 conference. Pls. let me know how to proceed. BTW: we would like to share a booth with affiliated company (W-IE-NE-R), I hope that would be possible. Pls. let me know your comments Best regards Maik Donix -- Maik Donix, Dipl.-Wi.-Ing. sales / Vertrieb | mobil:++49 172 6569 267 iseg Spezialelektronik GmbH | fon: ++49 351 269 9625 Bautzner Landstr. 23 | mail: maik.donix(a)iseg-hv.de D-01454 Radeberg OT Rossendorf | web: www.iseg-hv.de Geschäftsführer/Managing Director: Dr. Frank Gleisberg, Dr. Joachim Pöthig Registergericht/Lower District Court: Amtsgericht Dresden HRB 16250 Umsatzsteuer-Identnummer / VAT Id: DE 812 50 89 42 Diese E-Mail enthält vertrauliche und/oder rechtlich geschützte Informationen. Wenn Sie nicht der richtige Adressat sind oder diese E-Mail irrtümlich erhalten haben, informieren Sie bitte sofort den Absender und vernichten Sie diese Mail. Das unerlaubte Kopieren sowie die unbefugte Weitergabe dieser Mail ist nicht gestattet. This e-mail may contains confidential and/or privileged information. If you are not the intended recipient (or have received this e-mail in error) please notify the sender immediately and destroy this e-mail. Any unauthorized copying, disclosure or distribution of the material in this e-mail is strictly forbidden.

1 0

[Tipp2014] urgent enquiry
by Kajari Mazumdar 20 Jan '14

20 Jan '14

Dear Organizers of TIPP2014, This is on behalf of the conference committee for CMS collaboration, LHC. I am the coordinator of this conference and I would like to know if you will accept abstracts on behalf of the experiment or you prefer individuals submitting their own abstracts. Thank you for clarification. With kind regards -- Kajari Mazumdar

1 0

[Tipp2014] [Indico] New abstract submission: DYCHKANT, Alexandre
by noreply-indico-team＠cern.ch 19 Jan '14

19 Jan '14

The following email has been sent to DYCHKANT, Alexandre: === Dear Alexandre Dychkant, The submission of your abstract has been successfully processed. Abstract submitted: <https://indico.cern.ch/userAbstracts.py?confId=192695>. Status of your abstract: <https://indico.cern.ch/abstractDisplay.py?abstractId=17&confId=192695>. See below a detailed summary of your submitted abstract: Conference: Tipp 2014 - Third International Conference on Technology and Instrumentation in Particle Physics Submitted by: DYCHKANT, Alexandre Submitted on: 19 January 2014 21:37 Title: An Array of Spherically Dimpled Scintillating Cells for an Integrated Readout Layer Abstract content The CALICE collaboration has been developing calorimetry for particle flow algorithms based detectors. To measure particle shower development, a finely segmented calorimeter optimized for PFA must consist of millions of channels. A scintillator-based calorimeter with cells of size 30 x 30 x 3 mm3 and read out with silicon photo-multipliers (SiPMs) shows great promise. The construction and assembly challenges of a highly segmented, scintillator-SiPM calorimeter could be greatly reduced with full integration of the read out electronics into active calorimeter layers. An integrated readout layer (IRL) comprised of a multi-channel electronics board instrumented with SiPMs paired to an monolithic array of scintillator cells, would eliminate much of the labor intensive production associated with individual readout cells. In this presentation we discuss the development and performance of injection molded polystyrene arrays of 2x2 dimpled scintillator cells with a thickness of 3mm and individual cell area of about 900 mm2. (The dimpled or concave shaped cells ensure uniformity of response for a SiPM positioned at the center of the cell.) The performances of arrays of molded cells are compared to arrays of cells machined from sheets of polyvinyltolulene scintillator of same thickness. To improve performance of molded array the depth of dimple of single injection molded cell needs to be optimized. The light output, uniformity, and cross talk of the molded and machined cells irradiated with a Sr-90 source and measured with a SiPM in current mode are reported. Plans for initial particle beam tests of the complete IRL will be also discussed. Summary Primary Authors: Dr. DYSHKANT, Alexandre (Northern Illinois University) <dyshkant(a)nicadd.niu.edu> Dr. ZUTSHI, Vishnu (Northern Illinois University) <zutshi(a)nicadd.niu.edu> Prof. BLAZEY, Gerald (Northern Illinois University) <gblazey(a)nicadd.niu.edu> Co-authors: Prof. HEDIN, David (Northern Illinois University) <hedin(a)nicadd.niu.edu> Dr. FRANKIS, Kurt (Northern Illinois University) <kfrankis(a)nicadd.niu.edu> Abstract presenters: Dr. DYSHKANT, Alexandre Track classification: Sensors: 1a) Calorimetry Presentation type: --not specified-- Comments:

1 0

[Tipp2014] [Indico] New abstract submission: BONESINI, Maurizio
by noreply-indico-team＠cern.ch 17 Jan '14

17 Jan '14

The following email has been sent to BONESINI, Maurizio: === Dear Maurizio Bonesini, The submission of your abstract has been successfully processed. Abstract submitted: <https://indico.cern.ch/userAbstracts.py?confId=192695>. Status of your abstract: <https://indico.cern.ch/abstractDisplay.py?abstractId=16&confId=192695>. See below a detailed summary of your submitted abstract: Conference: Tipp 2014 - Third International Conference on Technology and Instrumentation in Particle Physics Submitted by: BONESINI, Maurizio Submitted on: 17 January 2014 15:03 Title: Performances of SiPMT array readout for fast time-of-flight detectors Abstract content Array of SiPMTs may be used, in place of fast conventional photomultipliers (PMTs), for the readout of scintillator based time-of-flight systems. These new detectors are insensitive to external magnetic fields, have lower cost than traditional PMTs and present a compact design. Comparison of the obtained timing resolutions as respect to the baseline one (~ 50 ps) obtained with Hamamatsu R4998 PMTs are reported. Results using arrays from Hamamatsu, SenSL, Advansid will be shown. Tests were done in laboratory both with cosmics and an home developed laser system, based on a fast Avtech pulse and a Nichia laser-diode, capable of simulating the signal from a MIP. Summary Primary Authors: Dr. BONESINI, Maurizio (Universita & INFN, Milano-Bicocca (IT)) <maurizio.bonesini(a)cmib.infn.it> Co-authors: BERTONI, Roberto (Univ. + INFN) <bertoni(a)mib.infn.it> DE BARI, Antonio (Universita' di Pavia) <antonio.debari(a)unipv.it> ROSSELLA, Massimo (Sezione INFN Pavia) <massimo.rossella(a)pv.infn.it> NARDO', Roberto (Sezione INFN e Universita' Pavia) <nardo(a)unipv.it> PRATA, Marco (Sezione INFN Pavia) <marco.prata(a)pv.infn.it> Abstract presenters: Dr. BONESINI, Maurizio Track classification: Sensors: 1d) Photon Detectors Sensors: 1e) Novel technologies Experiments: 2a) Experiments & Upgrades Presentation type: --not specified-- Comments:

1 0

[Tipp2014] [Indico] New abstract submission: BONESINI, Maurizio
by noreply-indico-team＠cern.ch 17 Jan '14

17 Jan '14

The following email has been sent to BONESINI, Maurizio: === Dear Maurizio Bonesini, The submission of your abstract has been successfully processed. Abstract submitted: <https://indico.cern.ch/userAbstracts.py?confId=192695>. Status of your abstract: <https://indico.cern.ch/abstractDisplay.py?abstractId=15&confId=192695>. See below a detailed summary of your submitted abstract: Conference: Tipp 2014 - Third International Conference on Technology and Instrumentation in Particle Physics Submitted by: BONESINI, Maurizio Submitted on: 17 January 2014 14:57 Title: Development of a Fast Diode-Laser based Calibration System for Time-of-Flight Systems Abstract content Scintillator based time-of-flight system may reach good intrinsic time resolution, by using fast scintillators and photomultipliers. Examples are the large time-of-flight system constructed for the HARP experiment at CERN PS (~150 ps detector resolution) or the most demanding time-of-flight system of the MICE experiment at RAL (~50-60 ps detector resolution). This level of intrinsic timing resolutions puts demanding requirements on the laser based calibration system for day by day time monitoring. Such as system may be realized by splitting a fast laser beam (FWHM~ 30 ps) to a fast photodiode, giving the START for the TDC system, and injecting the laser light into a system of fibers that transmit the pulse to the individual counters to be calibrated, giving the STOP signal. Due to the limited power of diode-laser systems (up to 1 W) extreme care must be put to minimize power losses. The choice of the type of optical fiber to be used (multimode vs single-mode)is another critical issue. Step-index multimode fibers has been chosen giving the best trade-off between input power loss minimization and timing properties of the system. A system based on optical switches, fused fiber splitters and a fast diode-laser will be described, together with the laboratory tests needed to optimize the choice of components and characterize completely the timing performances. Summary Primary Authors: Dr. BONESINI, Maurizio (Sezione INFN Milano Bicocca) <maurizio.bonesini(a)mib.infn.it> Co-authors: BERTONI, Roberto (Sezione INFN Milano Bicocca) <bertoni(a)mib.infn.it> DE BARI, Antonio (Sezione INFN e Universita' di Pavia) <antonio.debari(a)unipv.it> ROSSELLA, Massimo (Sezione INFN Pavia) <massimo.rossella(a)pv.infn.it> Abstract presenters: Dr. BONESINI, Maurizio Track classification: Experiments: 2a) Experiments & Upgrades Emerging technologies: 4d) Photonics Presentation type: --not specified-- Comments:

1 0

[Tipp2014] [Indico] New abstract submission: Dr. LIPTON, Ronald
by noreply-indico-team＠cern.ch 16 Jan '14

16 Jan '14

The following email has been sent to Dr. LIPTON, Ronald: === Dear Ronald Lipton, The submission of your abstract has been successfully processed. Abstract submitted: <https://indico.cern.ch/userAbstracts.py?confId=192695>. Status of your abstract: <https://indico.cern.ch/abstractDisplay.py?abstractId=14&confId=192695>. See below a detailed summary of your submitted abstract: Conference: Tipp 2014 - Third International Conference on Technology and Instrumentation in Particle Physics Submitted by: Dr. LIPTON, Ronald Submitted on: 16 January 2014 15:57 Title: Performance of Three Dimensional Integrated Circuits Bonded to Sensors Abstract content We report on the processing and performance of 3D integrated circuits (3DIC) bonded to silicon sensors. The circuits were part of the Fermilab-sponsored two-tier 0.13 micron run at Tezzaron/ Global Foundries. They include designs for the CMS track trigger, ILC vertex detectors, and x-ray correlation spectroscopy. Sensors were bonded to the 3DICs using die-to-die solder ball bonding as well as with a chip-to-wafer oxide bonding process (Ziptronix DBI) similar to the wafer-to-wafer bonding process used for the 3DICs. Summary Primary Authors: Dr. LIPTON, Ronald (Fermi National Accelerator Lab. (US)) <ronald.lipton(a)cern.ch> Co-authors: Dr. DEPTUCH, Grzegorz (Fermi National Accelerator Lab. (US)) <grzegorz.wladyslaw.deptuch(a)cern.ch> HOFF, Jim (Fermilab) <jimhoff(a)fnal.gov> THOM, Julia (Cornell University (US)) <julia.thom(a)cern.ch> WITTICH, Peter (Cornell University (US)) <pw94(a)cornell.edu> YE, Zhenyu (Fermi National Accelerator Lab. (US)) <zhenyu.ye(a)cern.ch> SIDDONS, Peter (Brookhaven National Laboratory) <siddons(a)bnl.gov> Prof. TRIPATHI, Mani (University of California Davis (US)) <sudhindra.mani.tripathi(a)cern.ch> HEINTZ, Ulrich (Brown University (US)) <ulrich_heintz(a)brown.edu> NARAIN, Meenakshi (Brown University (US)) <narain(a)hep.brown.edu> Mr. YAREMA, Ray (FNAL) <yarema(a)fnal.gov> GRYBOS, Pawel (High Energy Department) <grybos(a)ftj.agh.edu.pl> SZCZYGIEL, Robert (AGH UST) <robert.szczygiel(a)agh.edu.pl> TRIMPL, Marcel (Fermilab) <trimpl(a)fnal.gov> Abstract presenters: Dr. LIPTON, Ronald Track classification: Emerging technologies: 4c) 3D integration Presentation type: --not specified-- Comments:

1 0

[Tipp2014] [Indico] New abstract submission: SCOTTI, Valentina
by noreply-indico-team＠cern.ch 15 Jan '14

15 Jan '14

The following email has been sent to SCOTTI, Valentina: === Dear Valentina Scotti, The submission of your abstract has been successfully processed. Abstract submitted: <https://indico.cern.ch/userAbstracts.py?confId=192695>. Status of your abstract: <https://indico.cern.ch/abstractDisplay.py?abstractId=13&confId=192695>. See below a detailed summary of your submitted abstract: Conference: Tipp 2014 - Third International Conference on Technology and Instrumentation in Particle Physics Submitted by: SCOTTI, Valentina Submitted on: 15 January 2014 12:31 Title: The EUSO-Balloon Instrument Abstract content EUSO-Balloon is a pathfinder mission for JEM-EUSO (Extreme Universe Space Observatory on-board the Japanese Experiment Module), the near-UV telescope proposed to be installed on board the International Space Station (ISS) before the end of this decade. The main objective of this pathfinder mission is to perform a full scale end-to-end test of all the key technologies and instrumentation of JEM-EUSO detectors and to prove the entire detection chain. The JEM-EUSO instrument consists of an UV telescope designed to focus the signal of the UV tracks generated by Extreme Energy Cosmic Rays propagating in Earth’s atmosphere, onto a finely pixelized UV camera. The EUSO-Balloon instrument, smaller respect to the one designed for the ISS, is currently developed as a payload of a stratospheric balloon operated by the French Centre National d'Études Spatiales (CNES) and will be launched during the CNES flight campaign in August 2014. This telescope will point towards the nadir from a float altitude of about 40 km. With its Fresnel Optics and Photo-Detector Module, EUSO-Balloon will monitor a 12x12° wide field of view in a wavelength range between 290 and 430 nm, at a rate of 400’000 frames/sec. In this paper, we will review the main stages of the signal processing of the EUSO-Balloon instrument: the photodetection, the analog electronics, the trigger stages, which select events while rejecting random background, the electronic acquisition system which performs the data management and the monitoring, allowing the instrument control during operation. Summary Primary Authors: SCOTTI, Valentina () <scottiv(a)na.infn.it> Dr. OSTERIA, Giuseppe (INFN NA) <osteria(a)na.infn.it> Co-authors: Abstract presenters: SCOTTI, Valentina Track classification: Experiments: 2b) Astrophysics and Space Instrumentation Data-processing: 3b) Trigger and Data Acquisition Systems Presentation type: --not specified-- Comments: for the JEM-EUSO Collaboration

1 0

[Tipp2014] [Indico] New abstract submission: CRIDER, Ben
by noreply-indico-team＠cern.ch 13 Jan '14

13 Jan '14

The following email has been sent to CRIDER, Ben: === Dear Ben Crider, The submission of your abstract has been successfully processed. Abstract submitted: <https://indico.cern.ch/userAbstracts.py?confId=192695>. Status of your abstract: <https://indico.cern.ch/abstractDisplay.py?abstractId=12&confId=192695>. See below a detailed summary of your submitted abstract: Conference: Tipp 2014 - Third International Conference on Technology and Instrumentation in Particle Physics Submitted by: CRIDER, Ben Submitted on: 13 January 2014 05:59 Title: Kmax-based Event Mode Data Acquisition System for the University of Kentucky Accelerator Laboratory Abstract content The University of Kentucky Acceleratory Laboratory (UKAL), a facility that possesses unique experimental capabilities for the scattering and detection of monoenergetic fast neutrons, has recently invested in updating its data acquisition capabilities. Starting with a new system for high-precision singles measurements, where subsequent analysis leads to the extraction of lifetimes in the femtosecond region via the Doppler-shift attenuation method, we have developed an event-mode coincidence data acquisition system with capabilities that allow for a new range of experiments to be performed. The Kmax-based Event Mode Data Acquisition System at UKAL utilizes existing CAMAC modules and crates, as well as the Wiener CC-USB CAMAC controller. Developed with Sparrow Corporation's Kmax 10, utilizing Java 7 and widget-based toolsheets, the system allows for high throughput with low dead times. Currently, the system is capable of supporting 40 ADCs, 32-channels of TDC, 12-channels of scaler values, and 1 Mword of in-crate memory buffering. In this presentation, the commissioning, operation, and performance of the system will be described, and the particular design choices used for the graphical user interface and the logical flow of data acquisition and translation will be discussed. This material is based on work supported by U.S. National Science Foundation under Grant No. PHY-1305801 and the U.S. Department of Energy Nuclear Energy University Programs. Summary This talk describes a recent data acquisition system update for the University of Kentucky Accelerator Laboratory (UKAL). This update allows for a new range of experiments to be performed using monoenergetic fast neutrons at UKAL. Primary Authors: Mr. CRIDER, Ben (University of Kentucky) <ben.crider(a)uky.edu> Co-authors: Prof. PIERCEY, Buz (Eastern Kentucky University) <rodney.piercey(a)eku.edu> Abstract presenters: Mr. CRIDER, Ben Prof. PIERCEY, Buz Track classification: Data-processing: 3b) Trigger and Data Acquisition Systems Presentation type: --not specified-- Comments:

1 0

[Tipp2014] industry exhibition / iseg
by Maik Donix 10 Jan '14

10 Jan '14

Dear Madam or Sir, we are very interested to exhibit our high voltage power supplies during that conference. Pls. let me know if that possibility already included into sponsorship package? Your comments in that matter would be highly appreciated. Have a great weekend! Maik Donix -- sales / Vertrieb mobil:++49 172 6569 267 iseg Spezialelektronik GmbH fon: ++49 351 269 9625 Bautzner Landstr. 23 mail: maik.donix(a)iseg-hv.de D-01454 Radeberg OT Rossendorf web: www.iseg-hv.de Geschäftsführer/Managing Director: Dr. Frank Gleisberg, Dr. Joachim Pöthig Registergericht/Lower District Court: Amtsgericht Dresden HRB 16250 Umsatzsteuer-Identnummer / VAT Id: DE 812 50 89 42 Diese E-Mail enthält vertrauliche und/oder rechtlich geschützte Informationen. Wenn Sie nicht der richtige Adressat sind oder diese E-Mail irrtümlich erhalten haben, informieren Sie bitte sofort den Absender und vernichten Sie diese Mail. Das unerlaubte Kopieren sowie die unbefugte Weitergabe dieser Mail ist nicht gestattet. This e-mail may contains confidential and/or privileged information. If you are not the intended recipient (or have received this e-mail in error) please notify the sender immediately and destroy this e-mail. Any unauthorized copying, disclosure or distribution of the material in this e-mail is strictly forbidden.

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

tipp2014 January 2014