tipp2014

tipp2014@nikhef.nl

1261 discussions

[Tipp2014] [Indico] New abstract submission: MARINAS PARDO, Carlos
by noreply-indico-team＠cern.ch 28 Jan '14

28 Jan '14

The following email has been sent to MARINAS PARDO, Carlos: === Dear Carlos Marinas Pardo, The submission of your abstract has been successfully processed. Abstract submitted: <https://indico.cern.ch/userAbstracts.py?confId=192695>. Status of your abstract: <https://indico.cern.ch/abstractDisplay.py?abstractId=53&confId=192695>. See below a detailed summary of your submitted abstract: Conference: Tipp 2014 - Third International Conference on Technology and Instrumentation in Particle Physics Submitted by: MARINAS PARDO, Carlos Submitted on: 28 January 2014 15:18 Title: Ultra-transparent DEPFET pixel detectors for future electron- positron experiments Abstract content The DEPFET Collaboration develops highly granular, ultra-thin pixel detectors for outstanding vertex reconstruction at future collider experiments. A DEPFET sensor, by the integration of a field effect transistor on a fully depleted silicon bulk, provides simultaneously position sensitive detector capabilities and in-pixel amplification. The characterization of the latest DEPFET prototypes has proven that a comfortable signal to noise ratio and excellent single point resolution can be achieved for a sensor thickness of 50 micrometers. The close to final auxiliary ASICs have been produced and found to operate a DEPFET pixel detector of the latest generation with the required read-out speed. A complete detector concept is being developed for the Belle II experiment at the new Japanese super flavor factory. DEPFET is not only the technology of choice for the Belle~II vertex detector, but also a solid candidate for the ILC. Therefore, in this paper, the status of DEPFET R&D project is reviewed in the light of the requirements of the vertex detector at a future electron-positron collider. Summary Primary Authors: Dr. MARINAS, Carlos (University of Bonn) <cmarinas(a)uni-bonn.de> Co-authors: Abstract presenters: Dr. MARINAS, Carlos Track classification: Experiments: 2a) Experiments & Upgrades Presentation type: --not specified-- Comments:

1 0

[Tipp2014] [Indico] New abstract submission: DELLA PIETRA, Massimo
by noreply-indico-team＠cern.ch 28 Jan '14

28 Jan '14

The following email has been sent to DELLA PIETRA, Massimo: === Dear Massimo Della Pietra, The submission of your abstract has been successfully processed. Abstract submitted: <https://indico.cern.ch/userAbstracts.py?confId=192695>. Status of your abstract: <https://indico.cern.ch/abstractDisplay.py?abstractId=52&confId=192695>. See below a detailed summary of your submitted abstract: Conference: Tipp 2014 - Third International Conference on Technology and Instrumentation in Particle Physics Submitted by: DELLA PIETRA, Massimo Submitted on: 28 January 2014 13:42 Title: Deformation Monitoring of a Tracking Particle Detector using Fiber Bragg Grating sensors. Abstract content The frontier evolution of a gaseous tracking particle detector technology has been moved in developing Micro-Pattern Gas Detectors that can achieve unprecedented spatial resolution, high rate capability and large sensitive area. However, also the geometry of such kind of tracking detector, in spite of the particular technology used, has to be known with a precision of the order of few tens of μm. The relative position of each detector with respect to a reference system is usually measured through optical sensor elements (CCDs, lenses, light sources), but also any deformation (bending, strain, torsion) with respect to its ideal shape has to be monitored as well. From this consideration, a real-time sensing technology capable to detect any curvature and deformation of a detector with a resolution of few tens of μm is desirable. However any sensor to be integrated with the detector itself should ideally comply with many requirements in terms of radiation hardness, insensitivity to magnetic field, and so on. Fiber Bragg gratings (FBGs) seem to provide a suited solution. In fact, the fiber itself can tolerate very high levels of radiations, is insensitive to magnetic field and electromagnetic noise, and FBGs are intrinsic strain and temperature sensors with wavelength-encoded information, offer high multiplexing capability with reduction of cabling complexity and linear output. In this work FBG technology is proposed as suitable sensing solution for the real-time deformation monitoring of a tracking particle detector. As a demonstrative target, some FBG sensors have been integrated with a miniature detector support panel in order to investigate their potentialities/capabilities in detecting local strain and thus bending. Preliminary experimental results are presented and discussed. Summary Our case of study is to use an FBG sensors with a micromegas (an abbreviation for “micro mesh gaseous structure” (MM)), that is a micro patter gas detector. One mandatory issue for the correct operation of the MM detector is a precise monitoring of its panels’ flatness/deformation. The basic idea, proposed here for the first time, relies with the development of a deformation monitoring system based on FBG technology, where several FBG strain sensors are surface attached to both detector support panels. Measuring strain on both sides of the panel it is possible to obtain its local curvature that is related to the second derivatives of the shape described by the bent surface. Actually, if a planar surface is bent, a positive strain (tensile) is induced on a side and a negative strain (compressive) is induced on the other one: curvature is proportional to the their relative difference. On the contrary, if a same sign strain is measured on the two sides of the surface, a longitudinal deformation of the surface can be derived. Following this idea, the whole surface of the support panels can be subdivide into a proper number of elements that undergo simple deformation. Each element will be monitored by using FBGs attached to the surface of the panel. A mechanical Finite Element Method analysis of a full size support panel is necessary in order to determine the number and the dimension of these elements, taking into account the mechanical properties of the panel and performance requirements. The sensing principle of a fiber Bragg grating can be expressed as 〖∆λ〗_B/λ_B =S_ε ε+S_T ∆T where λB is the original Bragg wavelength under strain free and initial temperature condition, ΔλB is the variation in Bragg wavelength due to applied strain ɛ and temperature variation ΔT, and Sɛ and ST are the sensitivity coefficients to strain and temperature, respectively. It is worth noting that in order to measure the strain of an host material, temperature compensation of the FBG sensor is required. The resolution of these technology is of the order of 1 με , suitable for the physical requirements on the detector geometry. The obtained results prove that the proposed approach has the potentialities to permit a continue monitoring of the deformation and bending of the detector. Primary Authors: Dr. DELLA PIETRA, Massimo (Engineering Dept, University of Naples “Parthenope” and INFN) <massimo.della.pietra(a)cern.ch> Co-authors: Prof. CAMPOPIANO, Stefania (Engineering Dept, University of Naples “Parthenope”) <stefania.campopiano(a)uniparthenope.it> Prof. IADICICCO, Agostino (Engineering Dept, University of Naples “Parthenope”) <agostino.iadicicco(a)uniparthenope.it> Abstract presenters: Dr. DELLA PIETRA, Massimo Track classification: Sensors: 1c) Gaseous Detectors Emerging technologies: 4e) Precision engineering Presentation type: --not specified-- Comments: Our first choice on the track classification is "Emerging technologies: 4e) Precision engineering", the second one is Sensors: 1c) Gaseous Detectors

1 0

[Tipp2014] [Indico] New abstract submission: SCHWEGLER, Philipp
by noreply-indico-team＠cern.ch 28 Jan '14

28 Jan '14

The following email has been sent to SCHWEGLER, Philipp: === Dear Philipp Schwegler, The submission of your abstract has been successfully processed. Abstract submitted: <https://indico.cern.ch/userAbstracts.py?confId=192695>. Status of your abstract: <https://indico.cern.ch/abstractDisplay.py?abstractId=51&confId=192695>. See below a detailed summary of your submitted abstract: Conference: Tipp 2014 - Third International Conference on Technology and Instrumentation in Particle Physics Submitted by: SCHWEGLER, Philipp Submitted on: 28 January 2014 12:51 Title: High-Rate Properties of Drift Tube Chambers for HL-LHC Abstract content The Monitored Drift Tube (MDT) chambers of the ATLAS experiment provide muon track reconstruction with a spatial resolution of about 35 µm and efficiency of almost 100% up to the maximum expected background rates at nominal LHC luminosity. For much higher background rates, as they are anticipated for LHC luminosity upgrades (HL-LHC), sMDT chambers with 15 mm tube diameter, which is half the diameter of the MDT chambers, have been developed. Compared to MDT chambers, they suffer much less from space charge caused by background hits and provide more redundancy due to the higher packing density of the drift tubes. In the existing MDT front-end electronics, bipolar shaping is used to eliminate the long signal tail caused by the slowly drifting ions and to guarantee baseline stability at high rates. The undershoot of the bipolar shaping causes, however, signal pile-up of fast successive pulses. The impact of signal pile-up is equivalent to a higher discriminator threshold for the subsequent pulse and implies additional time slewing and degradation of the detection efficiency. A technical solution consists in an active baseline restorer. We present measurements of (s)MDT chambers under irradiation with the existing front-end electronics and with an alternative front-end chip featuring active baseline restoration and compare the performance. We also report on the development of a new version of the MDT front-end chip as a replacement for the existing one and with the option of a baseline restorer for future electronics upgrades. Summary The ATLAS Monitored Drift Tube (MDT) chambers consist of aluminum tubes with 30 mm diameter and a central sense wire with 50 µm diameter set to a potential of +3080 V. The drift tubes are operated with Ar/CO₂ (93/7) gas mixture at 3 bar absolute pressure, resulting in a gas amplification of 2×10⁴. The maximum electron drift time for hits near the tube wall is approximately 700 ns, ions can drift for several milliseconds causing long tails in the corresponding pulse shapes. The existing ASD (Amplifier-Shaper-Discriminator) front-end chip has been optimized for typical pulses of muon and background hits at rates of up to a few hundred kHz per channel. Bipolar shaping is used for baseline restoration, compensating partly the long ion tails. The typical time needed to arrive at the baseline after a hit is approximately 500 ns which is sufficient for the referred rates and the typical lengths of the MDT pulse trains. For the high luminosity upgrade of the LHC (HL-LHC), new drift tube chambers (sMDT) with reduced tube diameter - 15 mm instead of 30 mm - have been developed. They are operated with the same gas mixture and amplification as the 30 mm MDTs, leading to an operating voltage of 2730 V. As the drift velocity in the gas decreases with increasing drift radii, the maximum drift time is reduced from about 700 to 185 ns, resulting in considerably shorter pulse trains. This allows to operate the sMDT chambers at much higher rates with high efficiency. Measurements of sMDT chambers equipped with the existing ASD chip under photon and proton irradiation at rates of up to 1.5 MHz per channel show a considerable gain in the 3σ efficiency of sMDTs compared to MDTs with 30 mm diameter at high background rates. The improvement is limited, however, by the undershoot of the bipolar shaping and the long baseline restoration time of approximately 500 ns, respectively. Simulations suggest that reducing the baseline restoration time has the potential to improve the efficiency at rates of 1.5 MHz per channel from ~61% to ~76%. With increasing rates the yield is even higher. A possible approach for faster baseline restoration has been implemented in the front-end chip of the ATLAS Transition Radiation Tracker (TRT), the ASDBLR chip, with active baseline restorer (BLR). We present measurements and simulations of such a chip with active baseline restoration on sMDT and MDT chambers and evaluate the possible improvement on the efficiency and spatial resolution. A new version of the ASD chip is in development as a replacement for the existing one, with the option of a baseline restorer for future electronics upgrades. First simulation results with the new ADC chip will be shown. Primary Authors: SCHWEGLER, Philipp (Max-Planck-Institut fuer Physik (Werner-Heisenberg-Institut) (D) <philipp.schwegler(a)cern.ch> Co-authors: KORTNER, Oliver (Max-Planck-Institut fuer Physik (Werner-Heisenberg-Institut) (D) <kortner(a)mppmu.mpg.de> KROHA, Hubert (Max-Planck-Institut fuer Physik (Werner-Heisenberg-Institut) (D) <kroha(a)mppmu.mpg.de> NOWAK, Sebastian (Max-Planck-Institut fuer Physik (Werner-Heisenberg-Institut) (D) <sebastian.nowak(a)cern.ch> OTT, Sebastian (Max-Planck-Institut fuer Physik (Werner-Heisenberg-Institut) (D) <sebastian.ott(a)cern.ch> RICHTER, Robert (Max-Planck-Institut fuer Physik (Werner-Heisenberg-Institut) (D) <robert.richter(a)cern.ch> Abstract presenters: SCHWEGLER, Philipp Track classification: Sensors: 1c) Gaseous Detectors Presentation type: --not specified-- Comments:

1 0

[Tipp2014] [Indico] New abstract submission: KISHISHITA, Tetsuichi
by noreply-indico-team＠cern.ch 28 Jan '14

28 Jan '14

The following email has been sent to KISHISHITA, Tetsuichi: === Dear Tetsuichi Kishishita, The submission of your abstract has been successfully processed. Abstract submitted: <https://indico.cern.ch/userAbstracts.py?confId=192695>. Status of your abstract: <https://indico.cern.ch/abstractDisplay.py?abstractId=50&confId=192695>. See below a detailed summary of your submitted abstract: Conference: Tipp 2014 - Third International Conference on Technology and Instrumentation in Particle Physics Submitted by: KISHISHITA, Tetsuichi Submitted on: 28 January 2014 10:54 Title: Recent Status of Front-end Electronics for DEPFET pixel detectors for Belle-II Abstract content The Belle II experiment, which will start after 2015 at the Super-KEKB accelerator in Japan, will focus on the precision measurement of the CP-violation mechanism and on the search for physics beyond the Standard Model. To cope with considerably increased background, a pixel vertex detector (PXD) based on DEPFET technology has been developed. The PXD consists of two layers of DEPFET sensor modules located at 1.8 and 2.2 cm radii. Each module has a sensitive area, which is thinned down to 75 μm and steered with three types of ASICs: Switcher, Drain Current Digitizer (DCD) and Data Handling Processor (DHP). Switcher chips are designed to steer the pixel matrix of the sensitive area. The DCD chips digitize the drain current coming from the pixels. All ASICs will be directly bump-bonded to the balcony of the all-silicon DEPFET module. Its excellent spatial resolution (in the order of several microns) and low material budget was one of the decisive factors determining the choice of this technology for the first time. We report on the current status of the front-end electronics development, including the recent results from the first full-scale module prototype and chip testing. Summary The Belle-II pixel detector (PXD) has been developed based on DEPFET technology. The PXD requires three types of steering front-end electronics, and the development of the Data Handling Processor (DHP) is currently imperative. The DHP is designed to steer the readout from the DEPFET matrix by sending the control signals to the other two chips and sending the data off the module to the back-end data handling hybrid over a 15 m long electrical output link with a rate of 1.6 Gbps. Such high performance constraints for the digital data processing make the DHP implementation extremely challenging. Several conceptual solutions for the digital data processing blocks were proposed and implemented. Currently, three prototype DHPs have been produced with different technology and the first production version designed with a 65-nm standard CMOS technology has been delivered. The chip is currently under testing and is expected to be the production chip version, suitable for assembly on PXD modules. Primary Authors: KISHISHITA, Tetsuichi (University of Bonn) <kisisita(a)physik.uni-bonn.de> Co-authors: HEMPEREK, Tomasz (Universitaet Bonn (DE)) <hemperek(a)physik.uni-bonn.de> Dr. KRÜGER, Hans (University of Bonn) <krueger(a)physik.uni-bonn.de> LEMARENKO, Mikhail (Universitaet Bonn (DE)) <mikhail.lemarenko(a)cern.ch> Mr. LÜTTICKE, Florian (University of Bonn) <luetticke(a)physik.uni-bonn.de> Mr. GERMIC, Leonard (University of Bonn) <lgermic(a)uni-bonn.de> Dr. MARINAS, Carlos (University of Bonn) <cmarinas(a)uni-bonn.de> WERMES, Norbert (Universitaet Bonn (DE)) <wermes(a)uni-bonn.de> Abstract presenters: KISHISHITA, Tetsuichi Track classification: Experiments: 2a) Experiments & Upgrades Data-processing: 3a) Front-end Electronics Presentation type: --not specified-- Comments:

1 0

[Tipp2014] Open-Access Publishing of your Proceedings - EPJ Web of Conferences
by Isaline Boulven 28 Jan '14

28 Jan '14

1 0

[Tipp2014] abstract submission
by Merlin 28 Jan '14

28 Jan '14

Dear Sir/Madam, When submitting my abstract I was not able to select the preferred presentation type (I assume oral or poster). I'm not sure if this is intentional or not. mvg, Merlin Kole

1 0

[Tipp2014] [Indico] New abstract submission: KOLE, Merlin
by noreply-indico-team＠cern.ch 28 Jan '14

28 Jan '14

The following email has been sent to KOLE, Merlin: === Dear Merlin Kole, The submission of your abstract has been successfully processed. Abstract submitted: <https://indico.cern.ch/userAbstracts.py?confId=192695>. Status of your abstract: <https://indico.cern.ch/abstractDisplay.py?abstractId=49&confId=192695>. See below a detailed summary of your submitted abstract: Conference: Tipp 2014 - Third International Conference on Technology and Instrumentation in Particle Physics Submitted by: KOLE, Merlin Submitted on: 28 January 2014 09:24 Title: Neutron Background Detection for a Hard X-ray Balloon-borne Polarimeter Abstract content PoGOLite is a balloon-borne hard X-ray polarimeter. It determines polarisation by measuring the azimuthal angular distribution of Compton scattered photons in a plastic scintillator array. The use of an all plastic target yields a relatively large but low mass detection area. The dominant source of background for the polarisation measurements has been shown through Geant4 simulations to originate from high energy (MeV range) atmospheric neutrons. Neutrons can pass the instrument's Bismuth Germanium Oxide (BGO) anticoincidence shield undetected and subsequently scatter between plastic scintillator elements to produce a polarisation signature. A passive 15 cm thick polyethylene shield surrounding the polarimeter reduces the neutron induced background by an order of magnitude. The background level remains however significant, prompting the need for active monitoring of the continuously changing neutron flux. For this purpose PoGOLite makes use of a neutron sensitive phoswich scintillator cell. The phoswich cell consists of a 5 mm thick Lithium Calcium Aluminium Fluoride (LiCAF) scintillator, used for neutron detection. The LiCAF is surrounded by a BGO anticoincidence system. This small light weight detector can therefore be used to measure the neutron flux even in high radiation environments. This type of neutron detector was tested on a separate dedicated stratospheric balloon mission, called PoGOLino, prior to the PoGOLite flight which took place in July 2013. Results from both flights will be presented and implications on the polarisation measurements of PoGOLite from 2013 will be discussed. Summary Primary Authors: Mr. KOLE, Merlin (KTH - Royal Institute of Technology) <merlin(a)particle.kth.se> Co-authors: Prof. FUKAZAWA, Yasushi (Hiroshima University) <fukazawa(a)hep01.hepl.hiroshima-u.ac.jp> Dr. FUKUDA, Kentaro (Tokuyama Corporation) <ken-fukuda(a)tokuyama.co.jp> Mr. ISHIZU, Sumito (Tokuyama Corporation) <s-ishizu(a)tokuyama.co.jp> Dr. JACKSON, Miranda (KTH - Royal Institute of Technology) <miranda(a)particle.kth.se> Dr. KAWAGUCHI, Noriaki (Tokuyama Corporation) <n-kawaguchi(a)tokuyama.co.jp> Mr. KAWANO, Takafumi (Hiroshima University) <tkawano(a)hep01.hepl.hiroshima-u.ac.jp> Dr. KISS, Mozsi (KTH - Royal Institute of Technology) <mozsi(a)kth.se> Dr. MORETTI, Elena (KTH - Royal Institute of Technology) <moretti(a)particle.kth.se> Prof. PEARCE, Mark (KTH - Royal Institute of Technology) <pearce(a)particle.kth.se> Mr. RYDSTROM, Stefan (KTH - Royal Institute of Technology) <stefan(a)particle.kth.se> Dr. TAKAHASHI, Hiromitsu (Hiroshima University) <hirotaka(a)hep01.hepl.hiroshima-u.ac.jp> Dr. YANAGIDA, Takayuki (Kyushu Institute of Technology) <yanagida(a)lsse.kyutech.ac.jp> Dr. CHAUVIN, Maxime (KTH - Royal Institute of Technology) <maxime(a)particle.kth.se> Mr. VICTOR, Mikhalev (KTH - Royal Institute of Technology) <mikhalev(a)kth.se> Abstract presenters: Mr. KOLE, Merlin Track classification: Experiments: 2b) Astrophysics and Space Instrumentation Presentation type: --not specified-- Comments:

1 0

[Tipp2014] [Indico] New abstract submission: DUARTE RAMOS, Fernando
by noreply-indico-team＠cern.ch 28 Jan '14

28 Jan '14

The following email has been sent to DUARTE RAMOS, Fernando: === Dear Fernando Duarte Ramos, The submission of your abstract has been successfully processed. Abstract submitted: <https://indico.cern.ch/userAbstracts.py?confId=192695>. Status of your abstract: <https://indico.cern.ch/abstractDisplay.py?abstractId=48&confId=192695>. See below a detailed summary of your submitted abstract: Conference: Tipp 2014 - Third International Conference on Technology and Instrumentation in Particle Physics Submitted by: DUARTE RAMOS, Fernando Submitted on: 28 January 2014 08:44 Title: Engineering studies for the inner region of the CLIC detector concepts Abstract content The strict requirements in terms of material budget for the inner region of the CLIC detector concepts require the use of a dry gas for the cooling of the respective sensors. This, in conjunction with the compactness of the inner volumes, poses several challenges for the design of a cooling system that is able to fulfil the required detector specifications. This presentation introduces a detector cooling strategy using dry air as a coolant and shows the results of computational fluid dynamics simulations and experimental measurements used to validate the proposed strategy. Furthermore, the progress on the development of lightweight detector support structures that fulfil both mass and stiffness requirements is also reported. Summary Primary Authors: DUARTE RAMOS, Fernando (CERN) <fernando.duarte.ramos(a)cern.ch> Co-authors: NUIRY, Francois-xavier (CERN) <francois-xavier.nuiry(a)cern.ch> KLEMPT, Wolfgang (CERN) <wolfgang.klempt(a)cern.ch> VILLAREJO BERMUDEZ, Miguel-angel (Universidad de Valencia (ES)) <miguel.angel.villarejo.bermudez(a)cern.ch> Abstract presenters: DUARTE RAMOS, Fernando Track classification: Emerging technologies: 4a) Cooling and cryogenics Presentation type: --not specified-- Comments:

1 0

[Tipp2014] [Indico] New abstract submission: Mr. SAWADA, Ryu
by noreply-indico-team＠cern.ch 28 Jan '14

28 Jan '14

The following email has been sent to Mr. SAWADA, Ryu: === Dear Ryu Sawada, The submission of your abstract has been successfully processed. Abstract submitted: <https://indico.cern.ch/userAbstracts.py?confId=192695>. Status of your abstract: <https://indico.cern.ch/abstractDisplay.py?abstractId=47&confId=192695>. See below a detailed summary of your submitted abstract: Conference: Tipp 2014 - Third International Conference on Technology and Instrumentation in Particle Physics Submitted by: Mr. SAWADA, Ryu Submitted on: 28 January 2014 08:27 Title: Upgrade of MEG Liquid Xenon Calorimeter Abstract content The MEG experiment yielded the most stringent upper limit of the branching ratio of a flavor-violating muon decay $\mu\rightarrow e\gamma$ in 2013. To improve the sensitivity by one order of magnitude, a major upgrade of the detector is planed. The energy and position resolutions of the liquid xenon (LXe) gamma ray detector are limited near the entrance-window by the limited size of the photomultiplier tubes (PMTs). For the upgrade, 2-inch PMTs on the entrance-window are supposed to be replaced by $12\times12$ cm${}^2$ silicon photomultipliers (SiPMs). According to a simulation study, the higher granularity will improve the energy resolution from 2.4\% to 1.1\% and the position resolution from 5 mm to 2 mm around the entrance-window. To be used in LXe, SiPMs are required to be able to detect vacuum ultra-violet photons (175 nm), be operational in the LXe temperature (165 K) with high enough photo-detection efficiency (PDE) and the gain uniformity. A new type of SiPM is being developed and were tested in LXe. The single-photoelectron detection capability was confirmed, and the PDE for the LXe scintillation light was measured to be 17\%. To address an issue of long tail of the pulse due to the large capacitance, a new connection scheme (connecting signal and bias lines in series and in parallel, respectively) was proved to make the pulse shorter. A large prototype of the LXe detector with using $\sim$600 SiPMs will be built in 2014 followed by the construction of the full size detector, where $\sim$4000 SiPMs will be used. Summary Primary Authors: Dr. SAWADA, Ryu (ICEPP, the University of Tokyo) <sawada(a)icepp.s.u-tokyo.ac.jp> Co-authors: Abstract presenters: Dr. SAWADA, Ryu Track classification: Sensors: 1a) Calorimetry Sensors: 1d) Photon Detectors Presentation type: --not specified-- Comments:

1 0

Re: [Tipp2014] Tipp2014 Digest, Vol 4, Issue 8
by Niels van Bakel 28 Jan '14

28 Jan '14

Beste Leo, Zou jij onderstaande emails willen beantwoorden en eventueel de handleiding voor abstract submission op onze website willen aanpassen? Grt, Niels > Message: 2 > Date: Sat, 25 Jan 2014 11:46:21 +0530 > From: Kajari Mazumdar <kajari.mazumdar(a)gmail.com> > Subject: Re: [Tipp2014] TIPP2014 - Abstract submission open > To: tipp2014(a)nikhef.nl > Message-ID: > <CAGduToUPqnLGQMh3UYQds0Na5PgoSMcC1RE+BeQaTkZvDza+jA(a)mail.gmail.com> > Content-Type: text/plain; charset="iso-8859-1" > > Dear Organizers, > > This is on behalf of the Conference committee of CMS collaboration at LHC. > CMS is interested in submitting many abstracts for the conference, and I > have > 2 questions regarding this as the coordinator within the conference > committee. > > 1. In Indico, shall I submit all the abstracts with myself as the presenter? > 2. Not in all cases the tracks can be specified exclusively. Or several > abstracts > may fall into multiple categories. > > Could you kindly help me? > Kind regards -- Kajari Mazumdar On Jan 27, 2014, at 11:01 PM, tipp2014-request(a)nikhef.nl wrote: > > ------------------------------ > > Message: 5 > Date: Mon, 27 Jan 2014 14:43:51 -0600 > From: Mircea Bogdan <bogdan(a)edg.uchicago.edu> > Subject: [Tipp2014] Abstract > To: tipp2014(a)nikhef.nl, "Henry J. Frisch" <frisch(a)hep.uchicago.edu> > Message-ID: <52E6C507.5030508(a)edg.uchicago.edu> > Content-Type: text/plain; charset=ISO-8859-1; format=flowed > > Hello, > > One quick question: > Are there guidelines for the Summary? > > Thank you very much. > > Best regards, > > Mircea > > > > > ------------------------------ > > Message: 6 > Date: Mon, 27 Jan 2014 15:43:22 -0600 (CST) > From: Hassan Chagani <chagani(a)physics.umn.edu> > Subject: [Tipp2014] Questions re: TIPP2014 Abstract Submission > To: tipp2014(a)nikhef.nl > Message-ID: <alpine.LRH.2.02.1401271534210.6170(a)spartha.spa.umn.edu> > Content-Type: TEXT/PLAIN; format=flowed; charset=US-ASCII > > Dear Sir/Madam, > > I would like to submit an abstract for TIPP 2014, but had a few questions > regarding the abstract submission form. I did try to search for the > answers before writing this email, but to no avail. Hopefully, answering > my questions will not take up too much of your time. > > 1. There is a field titled 'Summary'. Although it is not a mandatory > field, I am not sure of what should be written there as the abstract seems > to fit better in the 'Abstract content' field. What is the purpose behind > the 'Summary' field? > > 2. It is not possible to specify the 'Presentation type'. Is this > deliberate? Will there be any poster sessions, or will the conference only > consist of talks? > > 3. What is the difference between a 'Primary Author' and 'Co-Author'? I > assume that the former can change the abstract, but the latter cannot. Is > this correct, and is this the only difference? > > Sorry if all of these questions have already been answered on your website > and I simply haven't been able to find the answers. Thank you in advance > for your help. > > Yours Faithfully, > > Hassan Chagani. > > Tate Laboratory of Physics > 116 Church Street SE > University of Minnesota > Minneapolis MN 55455 > USA > > > ------------------------------

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

tipp2014